Mesaverde Group sandstone units in 13 closely-spaced wells in the central and southern Piceance Basin of Colorado were correlated utilizing wireline log response quantitatively and qualitatively. Based on these correlations, the environmental subdivisions of the Mesaverde Group were characterized as follows. Paralic (upper mixed-marine) zone, occurring in the uppermost Mesaverde, includes thick sandstone units which are interpreted to be regionally continuous. Fluvial zone, containing point-bars 20 to 30+ ft thick, is interpreted to be correlatable to a maximum of 6800 ft. Paludal zone, which has insufficient data to adequately characterize the sand units. However, 63 percent of the units are correlatable across at least 139 ft. An approximation of the dimensional characteristics of Mesaverde sandstone units has potential applications in designing hydraulic fracturing treatments and estimating gas reserves more accurately. 16 figures, 2 tables
Data set containing results from constant mean stress - constant Lode angle true triaxial compression tests performed on Castlegate Sandstone. From the test preformed, the bedding plane and the strain type inside the band of sedimentary rocks can be related to stress histories. The goal of these tests are to understand the conditions that lead to localized deformation in porous sandstone which has geotechnical applications such as oil and natural gas production, carbon dioxide sequestration, and hazardous waste storage.
Includes test data from Confined Brazilian Tests. The tests were aim at investigating the rock failure envelope of four different lithologies including Indiana limestone, Scioto sandstone, Grey Berea sandstone, and Tennessee sandstone. Tables include the strength data obtained using load and damage controlled Brazilian tests on the six lithologies. Confine Brazilian tests are preformed by wrapping a sample in a copper jacket so that the confining fluid does not directly interact with the sample. Then a constant confining pressure is applied to the fluid to create a state of triaxial stress in the disc such that the disc center is under three nonzero and unequal principal stress components. By increasing the confining pressure, the least principal stress changes from tensile to compressive so that rock failure can be investigated over a wide range of stress conditions.
The objective of this project is to develop a comprehensive, interdisciplinary, and quantitative characterization of a fluvial-deltaic reservoir which will allow realistic inter-well and reservoir-scale modeling to be constructed for improved oil-field development in similar reservoirs world-wide. The geological and petrophysical properties of the Cretaceous Ferron Sandstone in east-central Utah will be quantitatively determined. Both new and existing data will be integrated into a three-dimensional representation of spatial variations in porosity, storativity, and tensorial rock permeability at a scale appropriate for inter-well to regional-scale reservoir simulation. Results could improve a reservoir management through proper infill and extension drilling strategies, reduction of economic risks, increased recovery from existing oil fields, and more reliable reserve calculations. Transfer of the project results to the petroleum industry is an integral component of the project.
The objective of this project is to develop a comprehensive, interdisciplinary, and quantitative characterization of a fluvial-deltaic reservoir which will allow realistic inter-well and reservoir-scale modeling to be constructed for improved oil-field development in similar reservoirs world-wide. The geological and petrophysical properties of the Cretaceous Ferron Sandstone in east-central Utah will be quantitatively determined. Both new and existing data will be integrated into a three dimensional representation of spatial variations in porosity, storativity, and tensorial rock permeability at a scale appropriate for inter-well to regional-scale reservoir simulation. Results could improve reservoir management through proper infill and extension drilling strategies, reduction of economic risks, increased recovery from existing oil fields, and more reliable reserve calculations. Transfer of the project results to the petroleum industry is an integral component of the project.
Injection and observation data from two Frio Brine Pilot experiments conducted near Houston, Texas by the Gulf Coast Carbon Center. The items in the "Frio Documents" folder provide details about the project and the data is provided in two folders Frio I and Frio II.
Full-Scale Laboratory Drilling Tests on Sandstone and Dolomite, Final Report; December 1977
Processed SEGY files from the FutureGen2 project. Data includes 5 categories of OVSP data with 15 lines in each category (all in TWT). VSP data was processed from Sterling Seismic.
This Petrel project features geomechanical models that takes advantage of existing modeling work from PNNL and expands upon its framework to included overlying and underlying geologic zones. Where available, geomechanical logs were incorporated into these models. While the existing CO2 storage interval and caprock (Mt. Simon Ss and Eau Claire Shale) were finely layered by PNNL, the overlying layers were more coarsely layered to limit cell count.
The objective of this project is to develop a comprehensive, interdisciplinary, and quantitative characterization of a fluvial-deltaic reservoir which will allow realistic inter-well and reservoir-scale modeling to be constructed for improved oil-field development in similar reservoirs world-wide. The geological and petrophysical properties of the Cretaceous Ferron Sandstone in east-central Utah will be quantitatively determined. Both new and existing data will be integrated into a three-dimensional representation of spatial variations in porosity, storativity, and tensorial rock permeability at a scale appropriate for inter-well to regional-scale reservoir simulation. Results could improve reservoir management through proper infill and extension drilling strategies, reduction of economic risks, increased recovery from existing oil fields, and more reliable reserve calculations. Transfer of the project results to the petroleum industry is an integral component of the project.
DOE/BC/14896-22
From the site: "The Assessment Unit is the fundamental unit used in the National Assessment Project for the assessment of undiscovered oil and gas resources. The Assessment Unit is defined within the context of the higher-level Total Petroleum System. The Assessment Unit is shown here as a geographic boundary interpreted, defined, and mapped by the geologist responsible for the province and incorporates a set of known or postulated oil and (or) gas accumulations sharing similar geologic, geographic, and temporal properties within the Total Petroleum System, such as source rock, timing, migration pathways, trapping mechanism, and hydrocarbon type. The Assessment Unit boundary is defined geologically as the limits of the geologic elements that define the Assessment Unit, such as limits of reservoir rock, geologic structures, source rock, and seal lithologies. The only exceptions to this are Assessment Units that border the Federal-State water boundary. In these cases, the Federal-State water boundary forms part of the Assessment Unit boundary."
From the site: "Cell maps for each oil and gas assessment unit were created by the USGS as a method for illustrating the degree of exploration, type of production, and distribution of production in an assessment unit or province. Each cell represents a quarter-mile square of the land surface, and the cells are coded to represent whether the wells included within the cell are predominantly oil-producing, gas-producing, both oil and gas-producing, dry, or the type of production of the wells located within the cell is unknown. The well information was initially retrieved from the IHS Energy Group, PI/Dwights PLUS Well Data on CD-ROM, which is a proprietary, commercial database containing information for most oil and gas wells in the U.S. Cells were developed as a graphic solution to overcome the problem of displaying proprietary PI/Dwights PLUS Well Data. No proprietary data are displayed or included in the cell maps. The data from PI/Dwights PLUS Well Data were current as of October 2001 when the cell maps were created in 2002."
From the site: "The Assessment Unit is the fundamental unit used in the National Assessment Project for the assessment of undiscovered oil and gas resources. The Assessment Unit is defined within the context of the higher-level Total Petroleum System. The Assessment Unit is shown here as a geographic boundary interpreted, defined, and mapped by the geologist responsible for the province and incorporates a set of known or postulated oil and (or) gas accumulations sharing similar geologic, geographic, and temporal properties within the Total Petroleum System, such as source rock, timing, migration pathways, trapping mechanism, and hydrocarbon type. The Assessment Unit boundary is defined geologically as the limits of the geologic elements that define the Assessment Unit, such as limits of reservoir rock, geologic structures, source rock, and seal lithologies. The only exceptions to this are Assessment Units that border the Federal-State water boundary. In these cases, the Federal-State water boundary forms part of the Assessment Unit boundary."
From the site: "Cell maps for each oil and gas assessment unit were created by the USGS as a method for illustrating the degree of exploration, type of production, and distribution of production in an assessment unit or province. Each cell represents a quarter-mile square of the land surface, and the cells are coded to represent whether the wells included within the cell are predominantly oil-producing, gas-producing, both oil and gas-producing, dry, or the type of production of the wells located within the cell is unknown. The well information was initially retrieved from the IHS Energy Group, PI/Dwights PLUS Well Data on CD-ROM, which is a proprietary, commercial database containing information for most oil and gas wells in the U.S. Cells were developed as a graphic solution to overcome the problem of displaying proprietary PI/Dwights PLUS Well Data. No proprietary data are displayed or included in the cell maps. The data from PI/Dwights PLUS Well Data were current as of October 2001 when the cell maps were created in 2002."
From the site: "Cell maps for each oil and gas assessment unit were created by the USGS as a method for illustrating the degree of exploration, type of production, and distribution of production in an assessment unit or province. Each cell represents a quarter-mile square of the land surface, and the cells are coded to represent whether the wells included within the cell are predominantly oil-producing, gas-producing, both oil and gas-producing, dry, or the type of production of the wells located within the cell is unknown. The well information was initially retrieved from the IHS Energy Group, PI/Dwights PLUS Well Data on CD-ROM, which is a proprietary, commercial database containing information for most oil and gas wells in the U.S. Cells were developed as a graphic solution to overcome the problem of displaying proprietary PI/Dwights PLUS Well Data. No proprietary data are displayed or included in the cell maps. The data from PI/Dwights PLUS Well Data were current as of October 2001 when the cell maps were created in 2002."
From the site: "The Assessment Unit is the fundamental unit used in the National Assessment Project for the assessment of undiscovered oil and gas resources. The Assessment Unit is defined within the context of the higher-level Total Petroleum System. The Assessment Unit is shown here as a geographic boundary interpreted, defined, and mapped by the geologist responsible for the province and incorporates a set of known or postulated oil and (or) gas accumulations sharing similar geologic, geographic, and temporal properties within the Total Petroleum System, such as source rock, timing, migration pathways, trapping mechanism, and hydrocarbon type. The Assessment Unit boundary is defined geologically as the limits of the geologic elements that define the Assessment Unit, such as limits of reservoir rock, geologic structures, source rock, and seal lithologies. The only exceptions to this are Assessment Units that border the Federal-State water boundary. In these cases, the Federal-State water boundary forms part of the Assessment Unit boundary."
From the site: "Cell maps for each oil and gas assessment unit were created by the USGS as a method for illustrating the degree of exploration, type of production, and distribution of production in an assessment unit or province. Each cell represents a quarter-mile square of the land surface, and the cells are coded to represent whether the wells included within the cell are predominantly oil-producing, gas-producing, both oil and gas-producing, dry, or the type of production of the wells located within the cell is unknown. The well information was initially retrieved from the IHS Energy Group, PI/Dwights PLUS Well Data on CD-ROM, which is a proprietary, commercial database containing information for most oil and gas wells in the U.S. Cells were developed as a graphic solution to overcome the problem of displaying proprietary PI/Dwights PLUS Well Data. No proprietary data are displayed or included in the cell maps. The data from PI/Dwights PLUS Well Data were current as of October 2001 when the cell maps were created in 2002."
From the site: "The Assessment Unit is the fundamental unit used in the National Assessment Project for the assessment of undiscovered oil and gas resources. The Assessment Unit is defined within the context of the higher-level Total Petroleum System. The Assessment Unit is shown here as a geographic boundary interpreted, defined, and mapped by the geologist responsible for the province and incorporates a set of known or postulated oil and (or) gas accumulations sharing similar geologic, geographic, and temporal properties within the Total Petroleum System, such as source rock, timing, migration pathways, trapping mechanism, and hydrocarbon type. The Assessment Unit boundary is defined geologically as the limits of the geologic elements that define the Assessment Unit, such as limits of reservoir rock, geologic structures, source rock, and seal lithologies. The only exceptions to this are Assessment Units that border the Federal-State water boundary. In these cases, the Federal-State water boundary forms part of the Assessment Unit boundary."
From the site: "Cell maps for each oil and gas assessment unit were created by the USGS as a method for illustrating the degree of exploration, type of production, and distribution of production in an assessment unit or province. Each cell represents a quarter-mile square of the land surface, and the cells are coded to represent whether the wells included within the cell are predominantly oil-producing, gas-producing, both oil and gas-producing, dry, or the type of production of the wells located within the cell is unknown. The well information was initially retrieved from the IHS Energy Group, PI/Dwights PLUS Well Data on CD-ROM, which is a proprietary, commercial database containing information for most oil and gas wells in the U.S. Cells were developed as a graphic solution to overcome the problem of displaying proprietary PI/Dwights PLUS Well Data. No proprietary data are displayed or included in the cell maps. The data from PI/Dwights PLUS Well Data were current as of October 2001 when the cell maps were created in 2002."
Although oil production in the Black Warrior basin of Alabama is declining, additional oil may be produced through improved recovery strategies, such as waterflooding, chemical injection, strategic well placement, and infill drilling. High-quality characterization of reservoirs in the Black Warrior basin is necessary to utilize advanced technology to recover additional oil and to avoid premature abandonment of fields. This report documents controls on the distribution and producibility of oil from heterogeneous Carboniferous reservoirs in the Black Warrior basin of Alabama. The first part of the report summarizes the structural and depositional evolution of the Black Warrior basin and establishes the geochemical characteristics of hydrocarbon source rocks and oil in the basin. This second part characterizes facies heterogeneity and petrologic and petrophysical properties of Carter and Millerella sandstone reservoirs. This is followed by a summary of oil production in the Black Warrior basin and an evaluation of seven improved-recovery projects in Alabama. In the final part, controls on the producibility of oil from sandstone reservoirs are discussed in terms of a scale-dependent heterogeneity classification.
Supporting Information text, figures, tables and dataset for Journal of Geophysical Research - Solid Earth manuscript: Chemo-mechanical alterations induced from CO2 injection in carbonate-cemented sandstone: An experimental study at 71°C and 290 bar by Wu, Luhmann, Rinehart, Mozley, Dewers, Heath, Majumdar.
This report describes research accomplishments achieved with funding provided through Department of Energy (DOE) Contract DE-FE0031686. The purpose of this DOE funding is to develop methods that can provide key information about stress fields that act on deep rocks without invading the earth to acquire that information. The research objective was to demonstrate methods that extract the azimuth directions of SHmax and SHmin stress in deep rocks from traditional seismic reflection data like the data that are used to explore for deep oil and gas reservoirs. Battelle performed two seismic investigations and achieved estimates of SHmax and SHmin azimuths in both efforts that agreed with local, non-seismic, ground-truth measurements of SHmax orientation. The first procedure utilized vertical seismic profiling (VSP) data; the second effort utilized three-dimensional (3D) seismic data.